-48V Hot-Swap Controllers
with External R
SENSE
______________________________________________________________________________________   11
In the event of a short circuit at the output, the input
supply may dip below the UV threshold, resetting the
circuit breaker. The MAX5948 cycles ON and OFF until
the short is removed, which can be minimized by creat-
ing a deglitching delay at the UV pin with a capacitor
from UV to V
EE
. This allows the input supply to recover
before the UV pin resets the circuit breaker.
Figure 10 shows a circuit that automatically resets the
circuit breaker after a current fault. Transistors Q2 and
Q3 along with C4, D1, R7, and R8 form a programma-
ble one-shot circuit. In normal operation, the GATE pin
is pulled high and Q3 is turned on, pulling node 2 to
V
EE
. Resistor R8 turns off Q2. When a short occurs, the
GATE pin is pulled low and Q3 turns off. Node 2 starts
to charge C4 and Q2 turns on, pulling the UV pin low
and resetting the circuit breaker. The instant C4 is fully
charged, R8 turns off Q2, UV goes high and the GATE
starts to ramp up. Q3 turns back on and pulls node 2
back to V
EE
. Diode D1 clamps node 3 at one diode
drop below V
EE
. The duty cycle is set to 10% to prevent
Q1 from overheating.
Undervoltage and Overvoltage Protection
The UV and OV pins can be used to detect undervolt-
age and overvoltage conditions. The UV and OV pins
are internally connected to analog comparators with
20mV of hysteresis. When the UV voltage falls below its
threshold or the OV voltage rises above its threshold,
the GATE pin is immediately pulled low. The GATE pin
is held low until UV goes high and OV is low indicating
that the input supply voltage is within specification.
The UV pin is also used to reset the circuit breaker after
a fault condition has occurred. The UV pin can be
pulled below V
UVL
to reset the circuit breaker.
V
EE
SENSE
GATE
DRAIN
V
DD
OV
UV
PWRGD
MAX5948A
-48V RTN
-48V RTN
(SHORT PIN)
*
-48V
*DIODES INC. SMAT70A.
R4
562k&
1%
R8
510k&
5%
R5
19.1k&
1%
R6
562k&
1%
R7
1M&
5%
R9
10k&
1%
R1
0.02&
5%
R3
18k&
5%
R2
10&
5%
C1
150nF
25V
C4
1礔
100V
Q1
IRF530
D1
1N4148
Q2
2N2222
Q3
ZVN3310
C2
3.3nF
100V
C3
100礔
100V
GATE
2V/div
NODE2
50V/div
1s/div
NODE 2
Figure 10. Automatic Restart After Current Fault
相关PDF资料
MAX5949BESA+T IC CNTRLR HOT SWAP 8-SOIC
MAX5950ETJ+ IC PWM CTRL HOT-SW 12V 32TQFN-EP
MAX5952CUAX+ IC PSE CNTRLR FOR POE 36-SSOP
MAX5953DUTM+ IC INTERFACE 802.3AF 48TQFN
MAX5954LETX+T IC PCI EXP/HOT-PLUG CTRLR 36TQFN
MAX5955BEEE+ IC DUAL HOT-SWAP CTRLR 16-QSOP
MAX5957AETN+T IC TRPL PCI EXP/HOT-PLUG 56-TQFN
MAX5960AECS+T IC CTRLR HOT-PLUG QD 80-TQFP
相关代理商/技术参数
MAX5948BESA-T 功能描述:热插拔功率分布 RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
MAX5949AESA 功能描述:热插拔功率分布 RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
MAX5949AESA+ 功能描述:热插拔功率分布 48V- Hot-Swap Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
MAX5949AESA+T 功能描述:热插拔功率分布 48V- Hot-Swap Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
MAX5949AESA+TG126 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:
MAX5949AESA-T 功能描述:热插拔功率分布 RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
MAX5949BESA 功能描述:热插拔功率分布 RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
MAX5949BESA+ 功能描述:热插拔功率分布 48V- Hot-Swap Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube